It is a special calcium carbonate finish mortar, extra white, to apply on brick walls, concrete blocks, mortars. Leaves a fine white finish with a high resistance, endurance and flexibility.

Characteristics

• Easy application by hand.
• Extra whiteness.
• Extra flexibility to avoid cracks on extreme conditions.
• Hidrofuge: Protects against humidity.
• Monocomponent.
• Interior and exterior use.

How to prepare?

1. This product is specially designed to be applicated by hand.
2. Mix PAPRESA SHIKKUI 0,2 with 6-7 litres of clean water by each 25 kg bag.

How to use as a finish mortar?

• Mix PAPRESA SHIKKUI 0,2 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel.
• Resultant coat width must be between 1 and 6 mm.

How to use as a joint paste?

• Mix PAPRESA SHIKKUI 0,2 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel or metal spatula.
• It can be used together with mesh or cover tape.

It is hemyhidrate CaSO4 1/2H20 reduced from natural gypsum stone. It is used in ceramic industry, and product of decoration products. It can be used as load plastic painting formula. It can also be used as base for production of gypsum mortars and wall smoothers.

Charactetistics

• Easy application by hand.
• Slow forging.
• Minimum retraction after forging.
• Better workability.
• Gypsum based products are not suitable for outdoor use. Stock in dry place. Humidity absortion can change physical properties.

How to prepare?

1. Sprinkle the gypsum powder over the water.
2. Mix with a mixing machine until getting a creamy paste.
3. Let it settle for some minutes.
4. Apply by hand with a trowel or spatula.

Prepared concrete, ready to use, once mixed with water for little construction works.

Characteristics

• Easy application.
• Do-it-yourself ideal ready product.
• Great commodity (cement, soil and gravel already mixed).
• High resistance.

How to prepare?

1. Pour the water first and then the concrete powder.
2. Mix in bowls in an approximated proportion of 2-2,5 litres by bag.
3. If more water than recommended is added, the consistence and resistance of the concrete will be reduced.

It’s a thick contruction gypsum for handy application and slow forging, for interior wall covering works.
Most common uses:

• Sujeción de tabiques y ladrillos.
• Guarnecidos en interiores.
• Tapado de rozas
• Pasta de agarre de materiales de construcción en interiores.

Characteristics

• Easy application by hand.
• Retarded.
• Minimum retraction after forging.
• Monocomponent.

How to prepare?

• Sprinkle the gypsum over the water.
• Mix with a mixer machine until getting a creamy paste.
• Let it settle during some minutes.
• Apply handly with a trowel or a spatula.

It’s a lightweight construction gypsum for mechanical application and slow forging for indoor wall covering.
Most common uses:

• Indoor wall fast covering.
• Indoor ceiling fast covering.

Characteristics

• Easy mechanical application
• Slow forging
• Minimum retraction after forging
• Monocomponent
• Incorporating perlite aggregate

How to prepare?

1. Mix the product with a 90% of water. Water quantities might change according to worker’s fluidity preferences.
2. Coat must be 10-15 mm

It’s a thick contruction gypsum for handy application and slow forging, for interior wall covering works.
Most common uses:

• Filling of wall-roof meetings.
• Filling of doors and windows pre-frames.
• Wireway covering.
• Electric box fixing.
• Indoor walls.

Characteristics

• Easy application by hand.
• Retarded.
• Minimum retraction after forging.
• Monocomponent.

How to prepare?

• Sprinkle the gypsum over the water.
• Mix with a mixer machine until getting a creamy paste.
• Let it settle during some minutes.
• Apply handly with a trowel or a spatula.

Ultrafast shutter impermeable glue to cover water leaks, pores in 20 seconds.
Impermeabilizer for interiors and exteriors, concrete supports, cement walls and floors, cement-lime mortars, fiber-cement, getting a type A impermeability during 10 days.

Characteristics

• Monocomponent grey powder.
• Ultrafast (Forges in 20 seconds).
• Impermeable.

How to prepare?

• • It is adviced to prepare little quantities of paste, 3 of cement per 1 of water, mix energetically and apply immediatly.
  • Never add water to forged product to continue using it.
  • Never add any product that is not indicated in this technical data.

How to use?

• • • There can be water coming out from the support.
    • Mix must be done handly, protected with a plastic glove and the product will be applicated with a strong pression with the hand when it starts getting hot and hard.
    • It is recommended to mix the quantity of product that can be used in one minute. If there is no impermeabilization, give a second coat after 2 minutes.

Where to use?

In the most common examples of water Ieaks: Cement pipes, cement water deposits, pits, terraces and aII kind of cement and concrete supports that want to be impermeabilized.
Using substrates: Cement, cement-Iime mortars, cement floors, concrete, fiber-cement, brick and rock.
Do not use: On wood or gypsum.

It’s a latex-based liquid with resins and special components to be mixed with mortar-glues, it reinforces and flexibilizes.
It also provides::

• Plasticity.
• More stickness.
• Better workability.
• More impermeability.

Characteristics

• Monocomponent.
• Flexible (deformable – elastic).
• Promotes more than 100% the resistance to snatching.
• Impermeabilize mortars.

How to prepare?

1. Shake the product before use.
2. Pour the ADESILATEX first and then, the mortar-glue.
3. Mix in bowls in an aproximated proportion of 6-6,5 litres per each 25 kgs.
4. Mix by hand or with electric mixer (better slow, 500 rpm) until getting a creamy paste.
5. Never add more ADESILATEX after the paste settles.

How to use?

Prepair the mortar paste substituting the water by ADESILATEX.
Once mixed the paste, it must be used like a normal mortar-glue:

• Extend the product with the straight edge of the trowel to ensure a full contact with the substrate.
• Apply the dented edge of the trowel (n.6-8) in squares of 1,5 – 2 m2.
• Check that no surfacial film is formed over the glue (in such a case, it’s enough to pass the trowel with some fresh product)
• After 24 hours, cover joints with tapazul mixed with ADESILÁTEX.

Note: For reinforcing paints, add 1 litre of ADESILATEX for each 6 paint litres.

Where to use?

For the possibility of priming for interiors and for outdoor works.
Using substrates: Brick, blocks, sandstone, terracotta, satined concrete, cement roofs, pools, fiber-cement, radiant roofs, wooden roofs, old tiles, paving stone.
Substrates must be solid, clean, dry and without deformations.

It’s a grey self-levelling mortar for cement and concrete floors or similars.
It’s used before the realization of works that require a totally plane surface, such as: Moquettes, cork floors, plastic tiles, floating parquet, sintetic coverers…

Characteristics

• Monocomponent mortar-glue.
• Self levelling.
• Thin coat application for interiors.
• Easy application on cement or concrete.
• Excelent adherent power.
• Coat up to 15 mm

How to prepare?

1. Pour the water first and then, the levelling paste.
2. Mix in bowls adding water until saturation.
3. Hand mix or with mixer machine (better slow, 500 rpm) until getting a creamy paste.
4. Let it settle during 5 minutes before application in order to additives act correctly.
5. Never add more water after the paste settles.

How to use?

The floor must be clean of grase and dust and slightly wet.
Prepare a fluent paste for pouring it well over the floor and that the levelling additives act correctly.
It’s not a refilling paste, it es designed to cover little irregularities.
Respect the expansion joints. It is advisable to use a ruler and a level to establish refilling levels.
Once extended the product, use a trowel to help levelling.
After application, Iet it harden during 24 hours and sand slightly the little marks the trowel might have left.

It is a special calcium carbonate finish mortar, extra white, to apply on brick walls, concrete blocks, mortars. Leaves a fine white finish with a high resistance, endurance and flexibility.

Characteristics

• Easy application by hand.
• Extra whiteness.
• Extra flexibility to avoid cracks on extreme conditions.
• Hidrofuge: Protects against humidity.
• Monocomponent.
• Interior and exterior use.

How to prepare?

1. This product is specially designed to be applicated by hand.
2. Mix PAPRESA SHIKKUI 1,5 with 6-7 litres of clean water by each 25 kg bag.

How to use as a finish mortar?

• Mix PAPRESA SHIKKUI 1,5 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel.
• Resultant coat width must be between 1 and 6 mm.

How to use as a joint paste?

• Mix PAPRESA SHIKKUI 1,5 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel or metal spatula.
• It can be used together with mesh or cover tape.

It is a special calcium carbonate finish mortar, extra white, to apply on brick walls, concrete blocks, mortars. Leaves a fine white finish with a high resistance, endurance and flexibility.

Characteristics

• Easy application by hand.
• Extra whiteness.
• Extra flexibility to avoid cracks on extreme conditions.
• Hidrofuge: Protects against humidity.
• Monocomponent.
• Interior and exterior use.

How to prepare?

1. This product is specially designed to be applicated by hand.
2. Mix PAPRESA SHIKKUI 0,5 with 6-7 litres of clean water by each 25 kg bag.

How to use as a finish mortar?

• Mix PAPRESA SHIKKUI 0,5 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel.
• Resultant coat width must be between 1 and 6 mm.

How to use as a joint paste?

• Mix PAPRESA SHIKKUI 0,5 with water, better with slow mixing machine until getting a creamy paste.
• Apply with trowel or metal spatula.
• It can be used together with mesh or cover tape.

It’s a grey refractory mortar for wide coat, prepaired against fire and high temperatures.
It’s applied in the construction of elements where there will be high temperatures such as ovens, chimneys, barbacues, fireplaces…

Characteristics

• Great resistance to high temperatures.
• Great adherence power for laying refractory elements.
• Monocomponent
• Easy to use

How to prepare?

1. Pour the water first and then, the refractory mortar.
2. Mix in bowls in an approximated proportion of 4,5 litres per each 25 kgs
3. It’s very important to not add more water than recommended because chemical and physical conditions of the product would be reduced.
4. Hand mix or with a mixing machine (better slow, 500 rpm) until getting a creamy paste.
5. Never add water after the paste settles.

How to use?

Once the paste is ready, it must be worked as a traditional mortar, for the following applications:

• Union of rebellious bricks
• Wide coat cement walls

It’s recommended to clean the pieces to join and moiste them if porousity is high.
It’s important that before the product forges, refractory bricks joints are touched up.

Where to use?

Ceramic material fixing, for interiors and exteriors.
Using substrates: Cement and cement-lime mortar walls Substrates must be solid, hard, clean and dry, without cracks or deformations.
Do not use: On metal, fiber-cement or wood (no flexible)

It’s a grey mortar ready to use mixed with water.
Its principal applications are given in little domestic use works for brick placing, walls, floors, etc…

Characteristics

• Easy application.
• Do-it-yourself indicated product.
• Great commodity (cement and sand already mixed).
• Great adherence power for aislant elements fixing.
• Monocomponent (Just add water).

How to prepare?

1. The mixing is traditional, like every mortar.
2. Add the water it needs, to user’s convenience until getting a strong and consistent (usually 4 litres per each 25 kgs).

How to use?

Ceramic material fixing, for interiors and exteriors.
Using substrates: Cement floors and walls, cement-lime mortar brick.
Substrates must be solid, clean, dry and without deformations.
Do not use: On metal, fiber-cement, wood and old tiles.
For these applications, mix PANZER with ADESILATEX.
Over concrete, mix MORTERO SECO with ADESILATEX.

It’s a grey mortar to be projected with machine on brick walls or concrete blocks, acting as a glue for the fiberglass boards or rockwool rolls.
Also for cement walls.

Characteristics

• Easy application with projection machinery.
• Great adherence power for aislant elements placing.
• Waterproof: Protects against humidity.
• Monocomponent.

How to prepare?

This product is specially designed to be applicated with projection machinery.
It’s recommended to adjust the machine in a 25% mortar/water relation and modify this relation until getting the paste density wanted.
The mortar/water relation may change depending on working conditions.
In case of hand application, mix in a 6-7 water litres bowl per each 25 mortar kgs.

How to use?

Project the mortar on the wall.
The water volume must be graduated to get a paste density with no slipping-off.
Once projected, mortar must be smoothed with a trowel, trying that all the surface is covered and eliminating at once possible air bags.
Resultant coat width must be between 5 and 8 mm.
Fix the fiberglass or rockwool panels through manual pression.
It’s recommended to place these aislant panels from up to down, for the panels that must be cutted are the ones down, in order to ease the work as much as possible.
Fix the panels during the «open time» (20 minutes).
Out of this time, its properties are reduced.

This paste is specially indicated for fixation and rejointment of gypsum board in interior walls.

Characteristics

• White powder to mix with water.
• Excellent workability for interiors.
• High performance.
• Suitable thicken for gypsum board rejointment.
• Mechanic or manual application.

How to prepare?

1. Pour the water in a bowl and then, the product in an approximated proportion of 12 litres each 25 kgs.
2. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
3. Let it repose 5 minutes for the additives to act correctly.
4. Mix energically until getting a proper density.

Notes: A shaking excess might cause an forging process acceleration.
Never use more water than recommended nor add more water after the paste settles.

How to use?

Is specially designed for gypsum board treatment, combinated with union tape.
Before sealing the joints, not completely jointed boards must be refilled.
The product application uses to be manual, introducing the product between the joints with a little spatula and placing a union tape afterwards.
The product gives the chance of mechanic work.
Once the joint is filled, cover and plaster the product area, let dry and cover the tape.
Cover the screws’ heads.
Apply the tape by the ceiling.
Use armed tape or metallic angular profile for out vertical angles (corners).
Joint paste can be used to repair little damages made in the board placing, as well as maintenance works.

Where to use?

Gypsum board rejointment, combinated with union tape.
Specially suitable for all kind of gypsum board with or without insulators, with lowered edges and cardboarded faces.
Do not use: On wet or frosted surfaces.

It’s a paste for 1 to 15 mm joints between tiles.
Suitable for any kind of tiles refilling and sealing.
Available in white and in colours.
Special colours can be done after development.

Characteristics

• Monocomponent (only needs water).
• 1-15 mm joint widths.
• Excellent workability and easy application.
• High hardness and frost resistant.
• Hydrofuge.

How to prepare?

1. Pour the water first and then, the paste.
2. Mix in bowls in an approximated proportion of 1,8 litres each 6 kgs.
3. It’s very important to not add more water than recommended, physical and chemical conditions of the product would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose during 5 minutes before application, in order to additives to act correctly and the, mix again before use.
6. Never add water after the paste settles.

How to use?

Rejointment must be done after 24 hours of the ceramics fixing.
Clean all the rests of adhesive from the joints.
Mix ‘Tapazul’ until getting a creamy paste without lumps.
Fill the joints with product; this operation can be done with different tools: Brush, filling gun, gum spatula…
Once the joints are filled, let the product reposes until it starts getting hard, when the product rests will be cleaned with a sponge.
After 24 hours of the rejointment, the surface can be cleaned with a wet cloth.

It’s a white mortar-glue, for medium-high absortion ceramics walls, for interiors and thin coat, over surfaces with gypsum presence such as:

• Gypsum board panels.
• Gypsum covered walls.
• Gypsum-covered brick walls.

Characteristics

• Monocomponent mortar-glue.
• No vertical slip.
• Thin coat application for interiors.
• Containing retainers that prevent that forging needed water is absorbed by the wall.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 7,5 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

Substrate must be clean and dry.
Extend the product with the straigh part of the trowel to ensure a full contact.
Apply the dented trowel (no. 5-7) in 1,5-2 m2 squares.
Check that no film is formed on the surface of the adhesive (in such a case, pass the trowel with some fresh product).
Place the ceramic leaving 2-3 mm joints.
We recommend to leave 3 mm expansion joints in the extremes of the walls.

Where to use?

Ceramic materials placing, for interiors.
Using substrates: Traditional gypsum covered walls, plaster, boards, gypsum boards, big format bricks and gypsum covered bricks.
Do not use: On metal, fibercement, wood, tiles and old tiles.
In these cases, mix the product with ADESILATEX 1000 .

It’s a grey mortar-glue, ready to fix big format bricks in exteriors and in dampness risk zones (kitchen, bathroom, storage rooms, cellars…)
For wall with high-medium absortion ceramics with thick coat (8-13 mm), over bricks and cement.

Characteristics

• Monocomponent mortar-glue (only needs water).
• No vertical slip.
• Thick coat application.
• Excellent workabilty by its thickness and plasticity
• High frost resistance.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

For wall building:
Prepare the paste as indicated.
Extend the product with the trowel over the ceramic pieces, for making the assembly in the usual way.

For ceramic placing in the walls.
Substrate must be clean and dry.
Apply the product with the dented trowel (no. 10-15) in 1,5 – 2 m2 squares.
Check that no surfacial film is formed over the adhesive (in such a case, pass the trowel with some fresh product).

Where to use?

Ceramic walls building with large format and traditional bricks, for interiors and exteriors.
Using substrates: Cement, cement-lime mortar, brick and cement floors.
Substrates must be solid, hard, clean, dry and without deformations.
Do not use: On metal, concrete or wood.

White semiflexible mortar-glue with a great impermeability and flexibility, suitable for tile fixing in swimming pools.
Also used for walls in wet areas.
Ceramics: Medium-low absortion.
To be used on concrete and cement walls and floors.

Characteristics

• Monocomponent.
• Semiflexible.
• Slip resistant.
• Thin coat application.
• Frost resistant and high humidity resistance.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

Substrate must be clean and dry.
In case of concrete, make sure of its retraction and that it has no curer or sealer products (in such a case, give a PRIMER coat before).
Extend the product with the straigh part of the trowel to ensure a full contact.
Apply the dented trowel (no. 5-7) in 1,5-2 m2 squares.
Check that no film is formed on the surface of the adhesive (in such a case, pass the trowel with some fresh product).
Over floors in a bad state, we recommend to use PANZER FLEX.
After 24 hours, cover the joints with TAPAZUL and impermeabilize with ADESILATEX 1000 .
To clean swimming pool tiles and reinforce joints, use TAPAZUL.

Where to use?

Ceramic material placing for exteriors, on swimming pools.
Using substrates: Concrete, cement, cement-lime mortar and cement floors.
Substrates must be solid, hard, clean and dry, without cracks or deformations.
Do not use: On metal, fiber-cement, wood (non flexible), tiles and old tiles.
In these cases, mix the product with ADESILATEX 1000 .

High performance mortar-glue with additives to increase resistance and give a high grade of elasticity and impermeability.
Indicated for low absortion coverages: Porcelanics, ceramics, marble, big size ceramics and heated floors.

Characteristics

• Monocomponent mortar-glue (Only needs water).
• Slip resistant.
• Thin coat application.
• Excellent workability.
• Manufactured from synthetic resins plastifiers and thickenners.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

Substrates must be clean and dry.
Extend the product with the smooth part of the trowel to ensure a complete contact with the substrate.
Use the dented trowel (no. 6-8) in 1,5 – 2 m2 squares.
Check that no surfacial film is formed over the adhesive.
In such a case, it’s enough to pass the trowel again with some fresh product.
Place the ceramic leaving 2-3 mm joints.

We recommend:

• To leave 3 mm expansion joints in the extremes of the walls.
• For floors, leave 6 mm perimeter joints.

Where to use?

Ceramic tiles fixing, for walls and floors, for interior and exterior. Also for underwater applications.
Substrates: Concrete, cement, cement-lime mortar, cement floors, heated floors, pools, gypsum board walls.
Substrates must be solid, clean and dry without cracks or deformations.

High performance mortar-glue with additives to increase resistance and give a high grade of elasticity and impermeability.
Indicated for low absortion coverages: Porcelanics, ceramics, marble, big size ceramics and heated floors.

Characteristics

• Monocomponent.
• Slip resistant.
• Thin coat application.
• High frost resistance and high impermeability grade.
• Manufactured from synthetic resins plastifiers and thickenners.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

Substrates must be clean and dry.
Extend the product with the smooth part of the trowel to ensure a complete contact with the substrate.
Use the dented trowel (no. 6-8) in 1,5 – 2 m2 squares.
Check that no surfacial film is formed over the adhesive.
In such a case, it’s enough to pass the trowel again with some fresh product.
Place the ceramic leaving 2-3 mm joints.

We recommend:

• To leave 3 mm expansion joints in the extremes of the walls.
• For floors, leave 6 mm perimeter joints.

Where to use?

Ceramic materials placing, for walls and floors, for interior and exterior.
Substrates: Concrete, cement, cement-lime mortar, cement floors, heated floors, pools, gypsum board walls.
Substrates must be solid, clean and dry without cracks or deformations.

It’s a white/grey cement-glue for fixing and bonding medium-high absortion ceramic tiles.
On the following substrates:

• Indoor and outdoor.
• Cement, concrete.
• Traditional brick..

Characteristics

• Monocomponent mortar-glue (Only needs water).
• Slip resistant.
• Thin coat application.
• Excellent workability for walls and floors.
• High frost resistance.

How to prepare?

1. Pour the water first and then, the mortar-glue.
2. Mix in bowls in an approximated proportion of 6 litres each 25 kgs.
3. It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced.
4. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
5. Let it repose 5 minutes for the additives to act correctly and then mix again before use.
6. Never add more water after the paste settles.

How to use?

Substrates must be clean and dry.
Extend the product with the smooth part of the trowel to ensure a complete contact with the substrate.
Use the dented trowel (no. 6-8) in 1,5 – 2 m2 squares.
Check that no surfacial film is formed over the adhesive.
In such a case, it’s enough to pass the trowel again with some fresh product.
Place the ceramic leaving 2-3 mm joints.

We recommend:

• To leave 3 mm expansion joints in the extremes of the walls.
• For floors, leave 6 mm perimeter joints.

Where to use?

Ceramic tiles fixing, for walls and floors.
Substrates: Cement, cement-lime mortar, brick and cement floors.
Substrates and surfaces must be solid, hard, clean and dry, without dust, grease or oxide.
Do not use: Over metal, concrete, fiber-cement, wood, tiles and old tiles.
In these cases, mix with ADESILATEX 1000 (6 litres each 25 kgs).

Is a gypsum-glue adhesive, for laying and bonding:

• BIG FORMAT BRICK.
• GYPSUM BOARDS.
• GYPSUM COVERED BRICKS.
• MOULDINGS – TILES.

Characteristics

• Excellent workability.Specially indicated for wall building.
• High performance.
• Minimum joint retraction.
• Great resistance to flexion and compression.
• Gran resistencia a la compresión y flexión.
• Monocomponent * Without slipping.

How to prepare?

1. Pour the water in a bowl and then the product in an approximated proportion of 17 litres each 25 kgs.
2. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
3. Let it settle 5 minutes for the additives to act correctly.

Notes: A shaking excess might cause a faster forging.
Never use more water than recommended or add water after the paste settles.

How to use?

BIG FORMAT BRICK WALLS
Place a expanded polystyrene strip glued in both faces over the framework.
Settle the first queue of pieces over the EPS with the male side up.
Once fixed the first queue, apply adhesive on the male and glue the laterals.
Place the panels, settling them with a rubber mallet.
The union of the roof is made with a mix of Papresa TABIQUE and gypsum.
Clean the joints after half hour.

GYPSUM BOARD WALLS
Present the gypsum boards over the brick wall.
Prepair the Papresa TABIQUE and the boards, cutting outlets, etc…
With a 10-15 dented trowel, apply the Papresa TABIQUE over the wall.
Stick the boards over the wall, pressing to compact it.
Clean the paste rests.
Apply and fill the joints with tape and PASTA DE JUNTAS Papresa.

Where to use?

Large format bricks, gypsum boards, gypsum covered bricks, gypsum-plaster walls, for interiors and plaster shelves.
Do not use: Outdoors

White gypsum-glue for plastering, repassing or smoothing of the following surfaces:

• Cement covered walls.
• Gypsum or lime covered walls.
• Brick or gypsum-covered bricks walls.
• Artex painted walls or until 2 mm wrinkled pastes.
• Also used to get rustic terminations in walls.

Characteristics

• Monocomponent gypsum-glue for interior use.
• Excellent workability for repassing and plastering gypsum walls with a thin coat.
• Finely textured surfaces.
• Minimum joint retraction.

How to prepare the paste?

1. Pour the water in a drawer and then the product until its saturation.
2. Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.
3. Let it settle for 5 minutes for the additives to act correctly.

Notes: A shaking excess might cause a faster forging.
Never use more water than recommended or add water after the paste settles.

How to use?

ON NEW CONSTRUCTION WALLS. (*)
The paste must be pasty but not very dense.
It will be applied with a trowel at least three days after placing the walls, with the outlets covered and in the finishing moment to be painted.
(*) Only over large format bricks and gypsum-covered bricks.

ON GOTELLET PAINTED WALLS.
Ready paste will be extended with a trowel over the surface which wants to be smoothed, like plastering.
Two layers must be given; one to «fill» the spot and once dry, a second termination layer will be given.
We recommend to sand superficially all the wall to eliminate all the dust and grease and increase it’s adherence grade at once.
It’s important that the wall is in good conditions and that layers are between 0,5 and 2 mm because absortion doesn’t allow a bigger load.

Where to use?

Paste for wall repairing and smoothing, artex painted or wrinkled pastes.
Using substrates: Brick, gypsum-covered bricks, cement, wrinkled paints, gypsum and lime.
Substrates must be solid, hard, clean and dry.
Do not use on: Metal fiber-cement, wood, old tiles or paving stones.