Grey / white panzer (C1T)

Grey / white panzer (C1T)

Cementitious tile adhesive for walls and floors. Indoor and outdoor

What is this product?


It's a white/grey cement-glue for fixing and bonding medium-high absortion ceramic tiles.


On the following substrates:


Cement, concrete.

Traditional brick.



Monocomponent mortar-glue (Only needs water).

Slip resistant.

Thin coat application.

Excellent workability for walls and floors.

High frost resistance.

How to prepare?


1- Pour the water first and then, the mortar-glue.

2- Mix in bowls in an approximated proportion of 6 litres each 25 kgs.

3- It is very important to not add more water than recommended, because physical and chemical conditions would be then, reduced. 4- Mix by hand or with a mixer machine (better slow, 500 rpm) until getting a creamy paste.

5- Let it repose 5 minutes for the additives to act correctly and then mix again before use.

6- Never add more water after the paste settles.

How to use?


Substrates must be clean and dry.

Extend the product with the smooth part of the trowel to ensure a complete contact with the substrate.

Use the dented trowel (no. 6-8) in 1,5 - 2 m2 squares.

Check that no surfacial film is formed over the adhesive.

In such a case, it's enough to pass the trowel again with some fresh product.

Place the ceramic leaving 2-3 mm joints.


We recommend - To leave 3 mm expansion joints in the extremes of the walls.

For floors, leave 6 mm perimeter joints.

Where to use?


Ceramic tiles fixing, for walls and floors.

Substrates: Cement, cement-lime mortar, brick and cement floors.

Substrates and surfaces must be solid, hard, clean and dry, without dust, grease or oxide.

Do not use: Over metal, concrete, fiber-cement, wood, tiles and old tiles.

In these cases, mix with ADESILATEX (6 litres each 25 kgs).

Technical data: Grey / white panzer (C1T)




Coat thickness in walls

Coat thickness in floors

Output in walls

Output in floors

Mix water

Open time according to UNE EN 1346

Rectification time

Initial adherence according to UNE EN 1348

Adherence after water immersion according to UNE EN 1348

Adherence after frost cicle according to UNE 1348

Fire reaction

Time for rejointment in walls

Time for rejointment in floors

Slip in vertical wall UNE EN 1308

Temperature during application

Paste density

Stockage (from manufacturing date, under cover, in a dry place)



White / Grey Powder

25 kgs

from 2 to 4 mm

from 5 to 7 mm

from 3,5 to 4 kgs/m2

from 6 to 9 kgs/m2

6-6,5 litres per each 25 kgs

20 minutes

10 minutes

1,3 N/mm2

0,5(grey)-0,9(white) N/mm2

1,1 N/mm2


4-6 hours

24 hours

< 0,5 mm

min 5ºC, max 32ºC

1,6 gr/cm3

12 months



White / Grey cement.

Siliceous soils.

Additives and resins.



Product components are not toxic.

It must be worked with gloves, avoid powder inhalation and contact with eyes and skin.

Keep away from children or animals.

First Aid


Skin: Wash with plenty of water

Eyes: Wash with plenty of water

Ingestion: Rinse with water and drink plenty of water

This technical data is written according to our knowledge and essays and doesn't assume any commitment. It's on customer's responsibility the admission and control in the distributor's warehouse or construction, as well as the election of the product to be used on each case. Manufacturer's responsibility is limited to manufacturation defects and for the value of the merchandise because it's out of his control the material election and the working conditions. Technical data for 2009.